Network Config : OT

[gmcust3]

I have 2 Lan Cards.

One I use for Lan and another for WAN. Till date I was using Broadband with a Static IP on Bridge Mode Modem.

When I do :Ifconfig I see :

## ifconfig
eth0 Link encap:Ethernet HWaddr 00:1C:C0:F1:D5:C2
inet addr:192.168.1.250 Bcast:192.168.1.255 Mask:255.255.255.0
inet6 addr: fe80::21c:c0ff:fef1:d5c2/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:556371 errors:0 dropped:0 overruns:0 frame:0
TX packets:537969 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:100
RX bytes:111342151 (106.1 MiB) TX bytes:128000465 (122.0 MiB)
Memory:e0300000-e0320000

eth1 Link encap:Ethernet HWaddr 00:18:F3:C9:0A:DC
inet addr:122.XXX.53.XXX Bcast:122.XXX.53.XXX Mask:255.255.255.0
inet6 addr: fe80::218:f3ff:fec9:adc/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:353932 errors:0 dropped:0 overruns:0 frame:0
TX packets:124640 errors:319 dropped:0 overruns:0 carrier:9
collisions:137 txqueuelen:1000
RX bytes:27302682 (26.0 MiB) TX bytes:12199644 (11.6 MiB)
Interrupt:169

lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:2886965 errors:0 dropped:0 overruns:0 frame:0
TX packets:2886965 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:363396178 (346.5 MiB) TX bytes:363396178 (346.5 MiB)

Now, today I got a lease line of 1 MB from same provider.Now, when I configure that I can ping but after 100 or so Ping, it gives me RTO.

My provider says It may be due to Half and Full Duplex Issue OR may be Nat issue.

## mii-tool
eth0: negotiated 100baseTx-FD flow-control, link ok
SIOCGMIIPHY on 'eth1' failed: Operation not supported

When I plug in Broadband , It shows Full Duplex when I restart.
When I plug in Lease , It shows Half Duplex when I restart.

Any advice what could be the reason ??



mii-tool -v
eth0: negotiated 100baseTx-FD flow-control, link ok
product info: vendor 00:aa:00, model 57 rev 0
basic mode: autonegotiation enabled
basic status: autonegotiation complete, link ok
capabilities: 100baseTx-FD 100baseTx-HD 10baseT-FD 10baseT-HD
advertising: 100baseTx-FD 100baseTx-HD 10baseT-FD 10baseT-HD flow-control
link partner: 100baseTx-FD 100baseTx-HD 10baseT-FD 10baseT-HD flow-control
SIOCGMIIPHY on 'eth1' failed: Operation not supported


Should I try below thing ...

http://www.cyberciti.biz/tips/howto-lin ... anent.html

Both nic are 100/1000.

[williamconley]

Now, I'm not saying you "Won't" get an answer to this question here on the Vicidial site ... but I will say that it's really not the appropriate venue for the question. That's fairly obvious. I know these guys are often "Godlike" in their abilities (noone can argue with that!), but this (seriously) is a pure networking question in no way related to Vicidial.

If you actually want good odds on getting an answer to your question, this should be asked on a networking site.