Voice Time USB

[carsonrose]

I have the voice time usb dongle installed. During installation, I did wanpipe-compile - per the manual.....Which I have been following to the letter.... It seems to go smooth, alot of output and then it finishes without errors. However:

Code: Select all

vici:~ # wanrouter hwprobe

FATAL: Error inserting wanpipe (/lib/modules/3.1.10-1.29-default/kernel/drivers/net/wan/wanpipe.ko): No such device

AND

Code: Select all

vici:~ # lsusb
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 003: ID 10c4:8460 Cygnal Integrated Products, Inc.
Bus 004 Device 002: ID 04ca:0050 Lite-On Technology Corp.


Notice it doesnt say anything about Sangoma...Just that Sygal junk...

**AND***

Code: Select all

Aug 12 23:53:59 vici kernel: [21705.995137] WANPIPE(tm) Hardware Support Module  3.5.28.0 (c) 1994-2010 Sangoma Technologies Inc
Aug 12 23:53:59 vici kernel: [21705.995542] usbcore: registered new interface driver sdlausb
Aug 12 23:53:59 vici kernel: [21705.998534] WANPIPE(tm) Interface Support Module 3.5.28.0 (c) 1994-2010 Sangoma Technologies Inc
Aug 12 23:53:59 vici kernel: [21705.995542] usbcore: registered new interface driver sdlausb
Aug 12 23:53:59 vici kernel: [21705.998534] WANPIPE(tm) Interface Support Module 3.5.28.0 (c) 1994-2010 Sangoma Technologies Inc
Aug 12 23:53:59 vici kernel: [21706.019041] WANPIPE(tm) Multi-Protocol WAN Driver Module 3.5.28.0 (c) 1994-2010 Sangoma Technologies Inc
Aug 12 23:53:59 vici kernel: [21706.019045] wanpipe: Probing for WANPIPE hardware.
Aug 12 23:53:59 vici kernel: [21706.019084] wanpipe: No AFT/S514/S508 cards found, unloading modules!
Aug 12 23:53:59 vici kernel: [21706.056550] usbcore: deregistering interface driver sdlausb


Is this a false error? Is my voicetime usb dongle working properly? I dont want to proceed to vicibox-install until I know this part is taken care of... Any ideas?

[vccsdotca]

Theres a lot of posts on this topic, the usb timer doesnt work with DAHDI 2.6. Contact sagnoma and explain to them most people that buy their usb device is for vicidial, as they dont seem to have insight into their customer base..

[carsonrose]

So I suppose my only alternative is to load a Vici build prior to Dahdi 2.6.... ?

[vccsdotca]

Well, you could do that.. Im not sure how it will affect performance as theres a lot of updates since then, even if using the SVN. I tried the reverse which was to re-compile dahdi and asterisk but the kernel is custom so it may cause massive issues. I would try the x100p if you have a pCi slot, other cards are very expensive. Kumba stated in reply to my previous post "We recommend you look at a Digium card of the Amfletec PCI-Express timers if you want something that works out of the box with ViciBox v.5.0".

Try ebay..

[carsonrose]

Will do... Thanks guys for your quick replies.. Always a pleasure to use the forums

[carsonrose]

Forgive me, but how do I mark this thread as "resolved"?

[carsonrose]

One last thing... How would I go about finding the latest build of Vici, prior to Dahdi 2.6?

[vccsdotca]

Seems like any iso prior to ViciBox v.4.0 RC1 according to release notes. http://www.vicidial.org/VICIDIALforum/v ... =8&t=25832

Also you'd have to change the subject of the topic to include "- RESOLVED"

[carsonrose]

Ok... so now I installed 3.1.15... same thing...

[vccsdotca]

Looks like from above that you dont have the driver installed, drivers and related troubleshooting is at http://wiki.sangoma.com/sangoma-wanpipe-voicetime , this would no longer be a vici issue.

[carsonrose]

VERSION: 2.8-409a
BUILD: 130809-1410

[carsonrose]

Code: Select all

Vici:~ # rasterisk
Asterisk 1.4.39.2-vici, Copyright (C) 1999 - 2010 Digium, Inc. and others.
Created by Mark Spencer <markster@digium.com>
Asterisk comes with ABSOLUTELY NO WARRANTY; type 'core show warranty' for details.
This is free software, with components licensed under the GNU General Public
License version 2 and other licenses; you are welcome to redistribute it under
certain conditions. Type 'core show license' for details.
=========================================================================
Unable to connect to remote asterisk (does /var/run/asterisk.ctl exist?)
Vici:~ # /etc/init
init.d/     initscript
Vici:~ # service vicidial restart
Asterisk not running

Router is already stopped !

Stopped Vicidial                                                                          done
Loading DAHDI drivers
Starting Sangoma wanrouter driver

ERROR: Wanpipe configuration file not found:
               /etc/wanpipe/wanpipe1.conf

Sangoma failed to load! Fallback to dahdi_dummy module!
FATAL: Error inserting dahdi_dummy (/lib/modules/2.6.34.10-0.6-default/weak-updates/extra/dahdi_dummy.ko): Unknown symbol in module, or unknown parameter (see dmesg)
dahdi_dummy NOT loaded