Manual dial issue.

All installation and configuration problems and questions

Moderators: gerski, enjay, williamconley, Op3r, Staydog, gardo, mflorell, MJCoate, mcargile, Kumba, Michael_N

Manual dial issue.

Postby Ahmed Hossam » Tue Dec 19, 2017 2:50 pm

Hi there,

Vicidial v2.14-506c BUILD: 161222-1111

When any of my agents trying to manual dial any number suddenly the call is disconnecting.
Error: (Dial Alert: Call Rejected: Chanunavail Cause: 1 - Unallocated(unassigned) number. SIP: 404 - Not found)
I thought that when the call on it's way to the customer, it doesn't reach him, i have no reason why, but actually i have a good enough connection to my provider so i am a little bit confused.
I think it's about the dialplan entry, but sitll trying to solve it..

Thanks.
Last edited by Ahmed Hossam on Thu Dec 21, 2017 12:25 pm, edited 2 times in total.
Ahmed Hossam
 
Posts: 7
Joined: Tue Dec 05, 2017 2:32 pm

Re: Disconnected number.

Postby kumar2arbind » Thu Dec 21, 2017 8:48 am

hi Ahmed

Give some more detail to us regarding your problem.

"I have received a call then suddenly it's "disconnected""

If i am right you mean to say that you log in to agent crm successfully with voice prompt "you are only person to this conference"
using your soft phone, if you did not hear the voice that mean you are not loged in correctly.
then
when inbound call land to agent crm it get disconnect. correct me if i am wrong.
kumar2arbind
 
Posts: 27
Joined: Mon Aug 29, 2016 2:01 am

Re: Disconnected number.

Postby Ahmed Hossam » Thu Dec 21, 2017 10:45 am

Hi,

Yes, they've heard "you're only person to this conference"

I edited the post for more explanation. Looking forward to hearing a solution.

Thanks for your response.
Ahmed Hossam
 
Posts: 7
Joined: Tue Dec 05, 2017 2:32 pm

Re: Manual dial issue.

Postby frequency » Thu Dec 21, 2017 8:46 pm

Ahmed Hossam wrote:Hi there,

Vicidial v2.14-506c BUILD: 161222-1111

When any of my agents trying to manual dial any number suddenly the call is disconnecting.
Error: (Dial Alert: Call Rejected: Chanunavail Cause: 1 - Unallocated(unassigned) number. SIP: 404 - Not found)
I thought that when the call on it's way to the customer, it doesn't reach him, i have no reason why, but actually i have a good enough connection to my provider so i am a little bit confused.
I think it's about the dialplan entry, but sitll trying to solve it..

Thanks.


This is carrier issue. If this is an old number on which you have dialed and talked to a customer and still receiving 404, please ask your carrier to remove such vendor from your routing or at least block this area code over that vendor because 404 calls would not route advance on their end and this is the final message. Same goes to sip 480. I think this is not a valid number hence a 404.
frequency
 
Posts: 117
Joined: Mon Jun 13, 2016 11:18 am

Re: Manual dial issue.

Postby kumar2arbind » Fri Dec 22, 2017 1:57 am

hi
Did you able to dial directly from sip phone rather then agent crm. and share your cli logs when you make manual call.
kumar2arbind
 
Posts: 27
Joined: Mon Aug 29, 2016 2:01 am

Re: Manual dial issue.

Postby blackbird2306 » Fri Dec 22, 2017 7:15 am

Post your carrier dialplan and dialed number (with country code) and also the asterisk cli logs from faulty calls as already mentioned.
Vicibox 6.0.2 from Vicibox_v.6.0.x86_64-6.0.2.iso | Vicidial 2.12-560a build: 160617-1427 | Asterisk 1.8.32.3
blackbird2306
 
Posts: 409
Joined: Mon Jun 23, 2014 5:31 pm


Return to Support

Who is online

Users browsing this forum: No registered users and 107 guests